Search

This is a high Tensile Bolt and Nut to fit through the Bottom of the Front Steering KnuckleM10 x 95mmto fit:Classic Fiat 500 all modelsFiat 126 all modelsIf you have any questions please contact us for help..

This is a high Tensile Bolt and Nut to fit through the Bottom of the Front Steering KnuckleM12 x 95mmto fit:Fiat 600Fiat 850If you have any questions please contact us for help..

This is a high Tensile Bolt and Nut to fit through the Bottom of the Front Steering KnuckleM14 x 95mmto fit:Fiat 600Fiat 850If you have any questions please contact us for help..

This is a Brand New Kit of TWO Stub Axles for the Left & RightThey have new top Bushes, Pins, Washers and Bushes and are ready to installThe Kit also comes with two new Hub Nuts(Once fitted they must be greased fully using a grease gun until the grease goes all the way through..

High Quality Productmade by major manufacturer in ItalyThis metal and rubber bush fits into the Front Leaf Spring at each end and also into the Front Stub AxleDimmensons:Inner Diameter [mm] 10Outer Diameter [mm] 27Height 1 [mm] 45Height 2 [mm] 51to..

High Quality Productmade by major manufacturer in Italy This metal and rubber bush fits into the Front Stub Axle/KnuckleDimmensons:Inner Diameter [mm] 12Outer Diameter [mm] 32Height 1 [mm] 34Height 2 [mm] 40 to fit:&nb..

Brand NewFactory Standard Cast Iron Front Upright for Stub Axles (SAME FOR BOTH SIDES)Ready to install and recondition your old existing Stub AxlesSupplied with a New King Pin Repair Kit (ONE SIDE ONLY)Parts Supplied1x. Stub Axle Upright1x King Pin Repair Kit1x Top ..

Fully Reconditioned Steering Boxfor Left Hand Drive Cars onlyPLEASE NOTE: The Shaft has 17 Splines on the Shaft where it meets the Steering Shaft inside the carto fit:Classic Fiat 500R & 126 all modelsPLEASE NOTE: This is a reconditioned part so we would need your old St..

Made in PolandThis Kit consist's of all the parts to overhaul ONE of Front Stub Axles(we would always recommend changing the top Stub Bushes at the same time, available above in related items)Fits:Classic Fiat 500 all modelsFiat 126 all modelsIf you have any ques..

This is the left hand side Front Hub Nut that screws onto the Stub AxleM14 x 1.5mmto fit:Classic Fiat 500 all models  (up to 1974)Fiat 126 all models (up to 1999)Fiat 600Fiat 850If you have any questions or queries please contact our office for h..

This is the right hand side Front Hub Nut that screws onto the Stub AxleM14x1.5mmto fit:Classic Fiat 500 all models  (up to 1974)Fiat 126 all models (up to 1999)Fiat 600Fiat 850If you have any questions or queries please contact our office for help..

Brand NewMade in ItalyThis is a two piece Bush Kit to fit the pedal boxPlease check these are correct for your car as there are two types availableto fit:Classic Fiat 500 F,L,RIf you have any questions please contact us for help..

These Stub Axles are fully factory reconditioned in Italy using Brass Bushes to last much longerThey have new top Bushes, Pins, Washers and Bushes and are ready to fit.These Stub Axles are made for the early models of 500’s with the smaller trach rods ends (10mm track rod hole)..

These Stub Axles are fully factory reconditioned in Italy using Brass Bushes to last much longerThey have new top Bushes, Pins, Washers and Bushes and are ready to fit.The Kit also comes with two new Hub Nuts(Once fitted they must be greased fully using a grease gun until the g..

These Front Stub Axles are fully factory reconditioned in ItalySupplied as a kit for both sidesThe Kit also comes with two new Hub Nuts(Once fitted they must be greased fully using a grease gun until the grease goes all the way through, then this procedure should be repeated ..

This is a Reconditioned Kit of TWO Stub Axles for the Left & RightThese kits have BRAND NEW UprightsRoller BearingsTop BushesKing Pin's WashersBrass Bushes Hub Nuts x2and are readyto installThis kit is also modified with bearings top and bottom for a smoother actionSupplied with two new Hub Nuts(Onc..

Made in ItalyHeavy Bronze Bush Sleeveto fit:Classic Fiat 500 all modelsIf you have any questions please contact us for help..

This simple tool was made to remove and install the threaded plug (see photos)to fit:Classic Fiat 500 all modelsFiat 126 all early modelsIf you have any questions please contact us for help..

Brand NewGenuine Fiat PartThis Worm Spindle is fitted inside the Steering Box and is prone to wear, cause play in the steeringto fit:Classic Fiat 500 all modelsFiat 126 all models (up to 1978)If you have any questions please contact us for help..

These Front Stub Axles are fully factory reconditioned in ItalySupplied as a kit for both sidesThe Kit also comes with two new Hub Nuts(Once fitted they must be greased fully using a grease gun until the grease goes all the way through, then this procedure should be repeated ..